Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision Last revision Both sides next revision | ||
|
projects:rfid [2016/05/29 22:05] over23 [READ NFC522 by node-red] |
projects:rfid [2016/06/14 03:52] over23 [Python to control GPI] |
||
|---|---|---|---|
| Line 6: | Line 6: | ||
| |**Materials:**| BananaPi, RFID-RC522, nepajive pole, kabely samec-samice s jumper konci, 5V napajeni, pajecka, pocitac s SSH| | |**Materials:**| BananaPi, RFID-RC522, nepajive pole, kabely samec-samice s jumper konci, 5V napajeni, pajecka, pocitac s SSH| | ||
| |**License:** | [[https://creativecommons.org/licenses/by-sa/3.0/|Uveďte původ-Zachovejte licenci; CC BY-SA]] | | |**License:** | [[https://creativecommons.org/licenses/by-sa/3.0/|Uveďte původ-Zachovejte licenci; CC BY-SA]] | | ||
| + | |||
| + | |||
| + | ===== on RaspberryPi 1b ===== | ||
| + | https://www.raspberrypi.org/documentation/configuration/device-tree.md | ||
| + | <code> | ||
| + | wget http://www.airspayce.com/mikem/bcm2835/bcm2835-1.44.tar.gz | ||
| + | tar -xvzf bcm2835-1.44.tar.gz | ||
| + | cd bcm2835-1.44 | ||
| + | ./configure | ||
| + | make | ||
| + | sudo make check | ||
| + | sudo make install | ||
| + | </code> | ||
| + | ===== TO STUDY ===== | ||
| + | * https://github.com/AdamLaurie/RFIDIOt - some tools | ||
| + | * http://jerrygamblin.com/2015/12/05/25-handheld-rfid-cloner/ - to clone | ||
| ===== RC522 vs BananaPi Pinout ===== | ===== RC522 vs BananaPi Pinout ===== | ||
| Line 15: | Line 31: | ||
| |CLOCK|23|GPIO11/SCLK |yellow | | |CLOCK|23|GPIO11/SCLK |yellow | | ||
| |SS|24|COE0#/GPIO07|green| | |SS|24|COE0#/GPIO07|green| | ||
| + | |||
| + | ==== RC522 vs RaspberryPI B ==== | ||
| + | {{projects:pythonraspberrypi_rfid.png}} | ||
| + | |||
| Reference: | Reference: | ||
| Line 48: | Line 68: | ||
| * http://raspmer.blogspot.cz/2015/07/how-to-use-rfid-rc522-on-raspbian.html | * http://raspmer.blogspot.cz/2015/07/how-to-use-rfid-rc522-on-raspbian.html | ||
| + | * !!!!! http://blog.infraserver.eu/?p=285 --> | ||
| + | |||
| + | * On Raspberry Pi, Device Tree usage is controlled from /boot/config.txt. By | ||
| + | default, the Raspberry Pi kernel boots with device tree enabled. You can | ||
| + | completely disable DT usage (for now) by adding: | ||
| + | <code> | ||
| + | device_tree= | ||
| + | </code> | ||
| <code> | <code> | ||
| [root@picka ~]# aptitude install python-dev | [root@picka ~]# aptitude install python-dev | ||
| Line 124: | Line 152: | ||
| sudo n stable | sudo n stable | ||
| # version can be switched by: sudo n 0.8.21 | # version can be switched by: sudo n 0.8.21 | ||
| + | |||
| + | [root@picka ~]# shutdown -r now | ||
| [root@picka ~]# node -v | [root@picka ~]# node -v | ||
| v6.2.0 | v6.2.0 | ||
| - | [root@picka ~]# npm install node-pre-gyp | + | [root@picka ~]# node-red-admin install node-red-node-irc |
| - | [root@picka ~]# npm install node-red-contrib-gpio | + | #[root@picka ~]# npm install node-pre-gyp |
| - | [root@picka ~]# npm install raspi-io | + | #[root@picka ~]# npm install node-red-contrib-gpio |
| - | [root@picka ~]# npm install node-red-node-irc | + | #root@picka ~]# npm install raspi-io |
| + | #[root@picka ~]# npm install node-red-node-irc | ||
| + | [root@picka ~]# shutdown -r now | ||
| </code> | </code> | ||