Differences
This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision Next revision Both sides next revision | ||
project:nodemcu_windev:en [2017/03/11 19:50] licho |
project:nodemcu_windev:en [2017/03/11 23:52] licho [Upload NodeMCU firmware] |
||
---|---|---|---|
Line 3: | Line 3: | ||
|**Related:**| | | |**Related:**| | | ||
|**Reference:**| https://Espressif.com | | |**Reference:**| https://Espressif.com | | ||
- | | **License:** | [[https://creativecommons.org/licenses/by-sa/3.0/|Uveďte původ-Zachovejte licenci; CC BY-SA]] | | + | | **License:** | [[https://creativecommons.org/licenses/by-sa/4.0/|Creative Commons Attribution-ShareAlike; CC BY-SA]] | |
===== Developer's IDE for nodeMCU on Windows 10 ===== | ===== Developer's IDE for nodeMCU on Windows 10 ===== | ||
Goal of this guide is to build Integrated Developement Environment (IDE) for work and development of nodeMCU solutions on operating system Windows 10. | Goal of this guide is to build Integrated Developement Environment (IDE) for work and development of nodeMCU solutions on operating system Windows 10. | ||
Line 23: | Line 23: | ||
In guide [[nodemcu_lbe:en|Linux Firmware Build Environment]] we went through steps how to compile nodeMCU firmware. Now we need upload firmware into ESP8266. For this purpose are available virious scripts and programs on the internet. Here we describe tool for Windows written in Delphi[[https://github.com/nodemcu/nodemcu-flasher|NodeMCU-Flasher]]. | In guide [[nodemcu_lbe:en|Linux Firmware Build Environment]] we went through steps how to compile nodeMCU firmware. Now we need upload firmware into ESP8266. For this purpose are available virious scripts and programs on the internet. Here we describe tool for Windows written in Delphi[[https://github.com/nodemcu/nodemcu-flasher|NodeMCU-Flasher]]. | ||
- | Before we start uploading firmware enable ''FLASH'' mode. Flash mode can enable by pushing ''FLASH'' button on nodeMCU or before reboot set ''GPIO0'' pin to value ''LOW''. [[nodemcu:en#Important warnings|Important warnings]] | + | Enable ''FLASH'' mode before start uploading firmware. Flash mode can be enabled by pushing ''FLASH'' button on nodeMCU or before reboot set ''GPIO0'' pin to ''LOW''. [[https://labka.cz/wiki/doku.php?id=project:nodemcu:en#important_warnings|Important warnings]] |
==== ESP8266 Flasher Tool ==== | ==== ESP8266 Flasher Tool ==== | ||
Line 71: | Line 71: | ||
Download ESPlorer [[http://esp8266.ru/esplorer/#download|here]]. | Download ESPlorer [[http://esp8266.ru/esplorer/#download|here]]. | ||
- | Supported platforms platformy: | + | Supported platforms: |
* Windows(x86, x86-64) | * Windows(x86, x86-64) | ||
Line 130: | Line 130: | ||
</code> | </code> | ||
- | For semi-automated I wrote in PowerShellu 5 [[https://github.com/lichnak/nodemcu-labka/blob/master/doc/wiki/cs/InstallMongoDB.ps1|MongDB Installation PowerShell Script]] | + | For semi-automated I wrote in PowerShell 5 [[https://github.com/lichnak/nodemcu-labka/blob/master/doc/wiki/cs/InstallMongoDB.ps1|MongDB Installation PowerShell Script]] |
==== Install Node.js ==== | ==== Install Node.js ==== | ||
Line 262: | Line 262: | ||
</code> | </code> | ||
- | Nyní můžeme spustit Node-RED editor na [[http://localhost:1880|http://localhost:1880]] | + | Now your can find your Node-RED editor installation at [[http://localhost:1880|http://localhost:1880]] |
{{project:wiki_nodemcu_windev_nodered.png}} | {{project:wiki_nodemcu_windev_nodered.png}} |